Wolf W482210 Manual do Utilizador

PRO S ERIESW ALL HOODS I NSTALLATIONI NSTRUCTIONS

Installation dimensions for 27-inch deep Pro Series wall hoods.10INSTALLATIONCONSIDERATIONS27-inch Deep Pro Series Wall Hoods1) A straight, short duct

30" TO 36"(762 - 914)TO COOKINGSURFACE30" TO 36"(762 - 914)TO COOKINGSURFACE18" (457)HEIGHTOF HOOD27"(686)DEPTHOF HOODWI

12Step 2: Wall PreparationIMPORTANT NOTE: Do not use ductsmaller than 10" round.IMPORTANT NOTE: Wolf recom-mends that the hood be installed amini

Step 3: Hood PreparationIf installing a duct cover assembly, seeduct cover installation on page 18.1) The hood assembly is shippedwith the rough-in pl

Step 5: Install the Hood1) Align both ends of the hoodassembly with the ends of the rough-in plate.2) Insert the back ends of the hoodassembly into th

15Step 6: Install Wiring1) Run 120 VAC, 15 amp (minimum)circuit electrical power cable from theservice panel to the junction box inthe rough-in plate.

WBLOWER-90INT (805086) orWBLOWER-120INT (804702)InstallationIMPORTANT NOTE: Wolf recom-mends installing the internal blowerto the rough-in plate assem

REMOTE BLOWERIMPORTANT NOTE: Before turningthe power on, make sure the bloweris in the "OFF" position. Use wire con-nectors or wire nuts app

18INSTALL DUCT COVER1) Attach duct cover from the insideof the hood through the filter open-ing using the screws provided.2) Leave the screws partiall

19P RO S ERIES W ALL H OOD A CCESSORIESBLOWERSInternal Blowers• 805347 – 600 CFM internal blowerfactory installed with ModelsW302210I, W362210I and L2

2I MPORTANT I NFORMATIONIMPORTANT NOTE: This appliancemust be installed in accordance withNational Electrical Codes, as well asall state, municipal an

20WARMING SHELFASSEMBLIESWarming shelf assemblies are avail-able for all Wolf wall hoods. Assemblyincludes 13" stainless steel panel withtwo fold

21Platinum Finish:• RAIL-30/PLT – Decorative rail for30" wall hoods.• RAIL-36/PLT – Decorative rail for36" wall hoods.• RAIL-42/PLT – Decora

22SERVICEINFORMATIONIMPORTANT NOTE: If the wall hooddoes not operate properly, followthese troubleshooting steps:• Verify that power is being supplied

CUT-OUT FOR LOGO PLACEMENTBOTTOM EDGE OF HOODFOLD LINE FOR LOGO PLACEMENTLEFT OUTER EDGE OF HOOD

WOLF APPLIANCE COMPANY, LLCP.O. Box 44848 •Madison, WI 53744 •800-332-9513www.wolfappliance.com805048 5/03

3P RO S ERIES W ALL V ENTILATION H OODS24-inch deep Pro Series wall hood overall dimensions18"(457 mm)24"(610 mm)48"(1219 mm)12"(3

INSTALLATIONCONSIDERATIONS22-inch and 24-inch DeepPro Series Wall Hoods1) A straight, short duct run willallow the hood to perform more effi-ciently.

30" TO 36"(762 - 914)TO COOKINGSURFACE30" TO 36"(762 - 914)TO COOKINGSURFACEE10" (254)18" (457)HEIGHTOF HOOD22" (55

622-INCH AND 24-INCH D EEP W ALL H OODS22-inch Deep Wall HoodsWidth Height of To Center of To Center ofModel Number of Hood (A) Transition (B) Transit

7Step 2: Wall PreparationIMPORTANT NOTE: Do not use ductsmaller than 8".IMPORTANT NOTE: Wolf recom-mends that the hood be installed aminimum of 3

4) Determine the discharge directionfor your installation and rotate backpanel accordingly. Your wall hoodback panel has been designed toaccommodate v

Step 4: Install the Hood1) Align the hood assembly with themarked location.2) Install #10 x 2" screws throughrough-in plate mounting holes.3) Att