Wolf CT36G/P Manual do Utilizador descarregar pdf (Página 2)

W OLF W ARMING D RAWER I NTEGRATED F RONT

P ANEL K IT I NSTALLATION I NSTRUCTIONS

Runners must be level, rigidly

mounted and capable of supporting

175 pounds (79kg).

Decorative wood front panel should

be a minimum of 1/2"(13) thick.

Follow Wolf Warming Drawer

Installation Instructions to Remove

Packaging, Electrical Requirements

and Grounding the Warming Drawer.

The cabinet for the warming drawer

must be:

• Depth: 26"

• Width: 33"

The opening for the warmingdrawer

must be:

• Depth: 25-1/2"(648) minimum from

inside back to front of cabinet frame.

• Width: 29-15/16"(760)

• Height: 10-3/8"(263)

• If installed under a wall oven: Allow a

2-3/8”(60) minimum between oven and

drawer cutouts for clearance of overlaps.

• If installed above a wall oven: Allow a

2"(51) minimum between oven and

drawer cutouts for clearance of overlaps.

Floor must be able to support 175

pounds (79kg).

The support frame:

• Width: 31-3/8"(797)

• Height: 10-7/8”(276)

• Thickness: 3/4"(19)

The support frame cut-out:

• Width: 28-1/2"(724)

• Height: 9-1/4"(235)

/4"

(235)

/8"

(276)

WARMING DRAWER

ROUGH OPENING

/4"(19) THICK WALL OVEN

SUPPORT PLATFORM

/4"(19) THICK

SUPPORT FRAME

/4"(19) THICK x 1

/2"(38)

PLYWOOD CLEAT

/4"(19) THICK PLATFORM

/4"(19) THICK

FACE PLATE

OVEN TRIM EXTENDS

/16"(8)

BELOW OVEN PLATFORM

2"(51) x 2" (51)

ANTI-TIP BLOCK

/2" min (648)

WARMING DRAWER ROUGH OPENING DEPTH

26" (660)

CABINET DEPTH

CABINET SIDE VIEW

/16"

(14)

/16"

(14)

/8"

(264)

ROUGH

OPENING

HEIGHT

/8"

(60)

33" (838)

CABINET WIDTH

/8" (979)

SUPPORT FRAME WIDTH

/2" (724)

SUPPORT FRAME OPENING

/2" (800)

CABINET FRONT VIEW

/16" (760)

WARMING DRAWER ROUGH OPENING WIDTH

/8"

(276)

/4"(19) THICK x 1

/2"(38)

PLYWOOD CLEAT

/4"(19) THICK

PLATFORM

/4"(19) THICK WALL OVEN

SUPPORT PLATFORM

/4"(19) THICK SUPPORT FRAME

2"(51) x 2" (51)

ANTI-TIP BLOCK

(REAR OF OPENING)

/4"

(235)

/16"

(14)

/16"

(14)

/8"

(264)

ROUGH

OPENING

HEIGHT

/8"

(60)

IMPORTANT NOTE: If you are installing the warming drawer in a frame-

less cabinet, it may be necessary to install 1/2"(13) wide cleats to accept

drawer mounting screws. See drawer for mounting hole locations.

Cabinet Support:

IMPORTANT NOTE: When installed in combination with a single oven,

check to be certain that any oven supports near the cutout do not

obstruct the 26" required cabinet depth of the warming drawer cutout.

• A 2-3/8"(60) minimum clearance between oven and warming drawer

cutouts are required. Additional clearance may be required if 2" x 4"(51 x

102) blocks are used to support runners or solid floor of the oven above.

• The warmer drawer may be supported by either a solid bottom, 2" x 4"

or 2" x 2"(51 x 102 or 51 x 51) runners.

• The support must be level, there is no way to level the drawer once it is

installed.

• The entire weight of the drawer is supported by the runners or solid

floor and must be capable of supporting 175 pounds (79kg).

Integrated Front Panel Panel Kit.qxd 10/10/2003 6:03 AM Page 2

1 2 3 4

Comentários a estes Manuais

Sem comentários

Wolf CT36G/P Manual do Utilizador Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com Fogões Wolf CT36G/P